Javascript required
Skip to content Skip to sidebar Skip to footer
Home / How to Remove Hex Screws Without a Hex Screwdriver

How to Remove Hex Screws Without a Hex Screwdriver

Download Article

Download Article

It happens often enough that you don't have a screwdriver handy but really urgently need to remove a screw. Although using a screwdriver is the easiest and safest way to remove a screw, there are different methods that can be attempted if you cannot find a screwdriver or cannot find the correct type and size of screwdriver.

  1. 1

    Use this method when trying to remove a Phillips head screw without the proper screwdriver. Phillips head screws are those that have two grooves forming a cross. In some cases one of the grooves will be longer than the other; if one groove is longer, this is the groove you should use when trying to unscrew your screw because it is easier to use with a variety of improvised tools.

    • Phillips head screws are particularly prone to being stripped, when the corners formed by the grooves are worn. This makes it very difficult to unscrew your screw because there are no longer solid grooves in which to insert your tool. Be very careful when using these methods so as not to strip your screw.

  2. 2

    Find a kitchen butter knife. Kitchen butter knives can be used in a very similar way to coins. Insert the end of the butter knife into the longer groove and turn counterclockwise to unscrew the screw.

    • If your butter knife is of low quality and strength or the screw is very tight, then you may bend your butter knife rather than unscrewing the screw. Be aware of this potential damage.[1]

    Advertisement

  3. 3

    Try a coin. Try inserting a small coin into the longer groove and seeing if it will turn the screw. Dimes and pennies are particularly useful for this method. This will usually only work for larger sized screws rather than very small ones.

    • Insert the coin into the larger groove and turn counterclockwise.

  4. 4

    Try pliers or vice grips. This will only work if the head of the screw is somewhat raised above the surrounding surface. Use the pliers or vice grips to grab the sides of the screw head and turn the screw counterclockwise to twist it out.

    • Needle nose pliers may work better than regular pliers.

  5. 5

    Use your thumbnail. Your thumbnail will only work if the screw is quite loose in the surface. Insert your nail into the longer groove and turn counterclockwise. If the screw is relatively loose then the screw should come out easily but if it is tight then this method likely will not work.

  6. 6

    Use an old CD. Insert the edge of an old CD into the longer groove and turn counterclockwise. This can damage and/or break the CD so make sure to use an old one that you don't mind damaging.

    • If the screw is very tight then this method might not work very well.

  7. 7

    Use a hacksaw to create a long groove in the screw, similar to a flat head screw. If your screw head is raised above the surface, you can use a hacksaw to create a groove similar to that of a flat head screw. Hold the hacksaw vertically and slowly cut the end of the screw to create a groove.

    • Make sure you do not cut the surface of the wood or whatever the screw is fastened to.
    • Remove the screw as you would a flat head screw, such as with a flat head screwdriver or another flat object such as a credit card.[2]

  8. 8

    Use a flat head screwdriver. If you can't find your Phillips head screwdriver but can find a flat head screwdriver, try using a flat head that is about the same length as the longer groove in the Phillips head screw. Insert the flat head into the longer groove and turn counterclockwise to unscrew.

    • This will not work with smaller screws, but it should be fine for normal size and larger screws.
    • Be careful not to damage your screw because there will now be less surface area in contact with the screw head.[3]

  9. 9

    Try a plastic toothbrush. Take a plastic toothbrush and lightly melt the end using a lighter or other source of heat. Once the plastic is soft you can insert it in the head of the screw and allow the plastic to harden once more. Once it is hard try to turn the screw counterclockwise to unscrew it.

    • This will usually only work with screws that are not too tight and relatively easy to turn.
    • Be very careful when using the lighter to avoid accidents and make sure to melt the toothbrush slowly so you can monitor the melting and prevent a mess from the melting plastic.

    Advertisement

  1. 1

    Use this method to remove a flat head screw without a screwdriver. A flat head screw has one groove across the head of the screw only. If you do not have a flat head screwdriver then you can usually use any kind of flat surface to unscrew the screw.

  2. 2

    Use a card. Try using a card such as a plastic credit card to turn the screw. Insert the edge of the card into the long groove and turn counterclockwise to unscrew the screw. Make sure the card is strong and old as it could be damaged in the process.

  3. 3

    Try the tab from a can of soda. Remove the tab from a can of soda and insert into the groove on the head of the flat head screw. Turn the head counterclockwise to unscrew the screw.

  4. 4

    Try a coin. Try inserting a small coin into the groove and turning counterclockwise to unscrew. Dimes and pennies are particularly useful for this method but larger coins will be easier to turn if they fit in the groove.

  5. 5

    Find a kitchen butter knife. Kitchen butter knives can be used in a very similar way to coins. Insert the end of the butter knife into the groove and turn counterclockwise to unscrew the screw.

    • If your butter knife is of low quality and strength or the screw is very tight, then you may bend your butter knife rather than unscrewing the screw. Be aware of this potential damage.

  6. 6

    Try pliers or vice grips. This will only work if the head of the screw is raised above the surrounding surface somewhat. Use the pliers or vice grips to grab the sides of the screw head and turn the screw counterclockwise to twist it out.

    • Needle nose pliers may work better than regular pliers.

  7. 7

    Use your thumbnail. Your thumbnail will only work if the screw is quite loose in the surface. Insert your nail into the groove and turn counterclockwise. If the screw is relatively loose then the screw should come out easily but if it is tight then this method likely will not work.

    Advertisement

  1. 1

    Use this method if you have a torx screw. Torx screws have a star-shaped pattern on the head and are very popular screws for all purposes. Security torx screws will have a nub in the middle of the screw head that needs to be accounted for.

    • Torx screws can be easy to damage so be very careful when using an alternative tool to unscrew these screws.

  2. 2

    Use a small flat head screwdriver. Insert the flat head screwdriver between two opposite edges of the screw head. Turn counterclockwise to remove the screw. Make sure you turn slowly so as not to damage the head.

    • For security torx screws you will need to insert the flat head in against one of the outer grooves and the center nub of the head. This works much the same as non-security torx screws.
    • Security torx screws will usually turn the opposite direction, so you should turn clockwise to remove them.

  3. 3

    Break out the pin on security torx screws. If you have a normal torx screwdriver but not a security version then you can simply remove the center pin out of the screw head. Take a hammer and a punch or other chisel-like tool and line up the chisel at the bottom of the pin. Gently tap on the top of the chisel to remove the center pin.[4]

  4. 4

    Drill a small hole in the tip of your torx driver. If you have a security torx screw and wish to remove using a non-security torx driver or drill bit then you can drill a small hole in the drill bit. This way it has a small hole to accommodate the center pin on your security torx screw.

  5. 5

    Try a plastic toothbrush. Take a plastic toothbrush and lightly melt the end using a lighter or other source of heat. Once the plastic is soft you can insert it in the head of the screw and allow the plastic to harden once more. Once it is hard try to turn the screw counterclockwise to unscrew it.

    Advertisement

  1. 1

    Use this method for removing very tiny screws without a screwdriver. Very tiny screws are particularly difficult to remove without the proper tools. They are often found on electronics devices. If you can, use an eyeglass repair kit to remove your screws, which will have the necessary tiny screwdrivers.

    • If you cannot find or use an eyeglass repair kit then you can try one of these methods.
    • Eyeglass repair kits are very cheap and easy to find.

  2. 2

    Try the tip of a knife. Use the pointed tip of a knife to turn tiny screws counterclockwise. Insert the knife tip into the groove; if you can, try inserting the knife tip at a slight angle to provide more contact surface area between the knife and the screw.

  3. 3

    Use a metal nail file. Use the tip of a metal nail file to insert into the groove on the top of the screw head. Turn the screw counterclockwise, being careful not to damage the head.

  4. 4

    Use the tip of pointy little scissors. Insert the tip of very pointy scissors into one of the grooves on the screw head. Turn the screw counterclockwise.

    • Blunt scissors will not work well for opening very small screws.

  5. 5

    Try the tip of tweezers. Insert the pointy tip of tweezers into the groove on the screw head and turn counterclockwise. The tip of tweezers must be pointy to be inserted into the groove properly.

    Advertisement

Add New Question

  • Question

    If I use it without a screwdriver how do I screw it back in again?

    Community Answer

    Use anything listed in the article to screw it back in.

  • Question

    What can I use to unscrew a screw in my phone?

    Community Answer

    Perhaps a small-sized Phillips, a small torx or possibly a pentalobe screwdriver. You'll need to determine what type is needed for your phone.

  • Question

    What do I do if the screw is too small?

    Community Answer

    You will need to find a larger one.

  • Question

    How do I remove an extremely small screw?

    Community Answer

    A set of jeweler's/eyeglasses screwdrivers may be required.

  • Question

    How do I fix a stripped screw on a door panel?

    Community Answer

    Use a stripped screw remover tool to remove the old screw and replace with a newer one.

  • Question

    How do I unscrew a small screw that's very tight?

    Noëlle Dailey

    Noëlle Dailey

    Community Answer

    Use the part of a nail clipper that gets the dirt from under the nails. Just a reminder some nail clippers don' have one of these files.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

  • For unusual screws such as those in electronics devices you may need to acquire a specialist tool as attempting to undo these without the correct tool may either invalidate the warranty or damage the screw to a degree where it will not be able to be removed without drilling it out.

  • Remember that a shop purchased screwdriver will always perform better than any adapted method. Always try to use a screwdriver where possible that is designed to remove the screw.

  • Carry a small tool kit with you wherever you go to avoid getting into needing to improvise a screwdriver.

  • Tool kits can be purchased from most good hardware/DIY stores worldwide and are good investments to solve the most common of basic tasks around the home, garden and garage.

  • When using any of the methods make sure you turn slow and steady to avoid damaging the screw head in the process of removing it.

  • Try spraying a little WD-40 on the screw before attempting to remove it. This might help loosen the screw and make it easier to remove[5]

  • If you really cannot remove the screw, try drilling out the screw with a drill bit that is slightly smaller than the shaft of the screw.

  • Turning a very tight screw slowly can permanently twist or strip a screwdriver or damage your workpiece. Using an offset or L-shaped tool, tap the driving tool (gently until you know you need more force) with a hammer to loosen the connection. Also the only method for removing the nut that locks a circular saw blade.

Thanks for submitting a tip for review!

Advertisement

  • Take care when using knives or improvised devices to remove screws as these can be dangerous to use in a manner with which they were not designed.

  • Always use power tools appropriately and be careful to keep moving parts away from your body to prevent injury. Follow all safety precautions recommended by the manufacturer.

  • Always be careful when using a lighter to melt the toothbrush. Keep flame away from body parts and any flammable objects to prevent a potential fire.

  • Using inappropriate tools to unscrew screws may invalidate the warranty on certain electronic devices.

Advertisement

About This Article

Article SummaryX

To unscrew a screw without a screwdriver, use a butter knife, coin, credit card, or the tab from a soda can to twist the screw counterclockwise. You can also grip the screw with a pair of pliers and try unscrewing it that way. If it's a tiny screw, use the tip of a knife or a pair of tweezers to unscrew it. To unscrew a Torx screw without a screwdriver, lightly melt the end of a plastic toothbrush and press it into the top of the screw. Once the end toothbrush hardens into the shape of the screw, try twisting it counterclockwise until it comes out. If you want to learn how to remove small screws with a nail file or tweezers, keep reading the article!

Did this summary help you?

Thanks to all authors for creating a page that has been read 1,122,633 times.

Did this article help you?

How to Remove Hex Screws Without a Hex Screwdriver

Source: https://www.wikihow.com/Unscrew-a-Screw-Without-a-Screwdriver